Atlas® Aluminum Marker Trays with Square Corners

Our Price:
Share this:
Atlas Square Corner Aluminum Marker Tray
Atlas Square Corner Aluminum Marker TrayAtlas Square Corner Aluminum Marker Tray

Atlas® aluminum marker trays have a blade style shelf or marker ledge that is 2 ¼" inches deep. The back of the tray is 2 1/8" wide and the ends of the ledge are cut square.

You can order full length trays up to 8' in length or two-piece trays up to 16' in length and they can all ship by UPS. Because the ends of the trays are square cut you can butt them up tightly against each other to create marker trays almost as long as you like without the added expense of shipping by truck. Altas® marker trays and ledges are carefully packed in heavy duty shipping tubes.

Extra-long Atlas® marker trays are also available as a single length up to 12' with either square cut corners or angle cut corners. These extra long aluminum marker trays ship by truck.

Atlas® aluminum marker trays are all made in the U.S.A. Note: Cut tolerances on all marker trays is +/- ¼"

Atlas® marker trays are an OptiMA exclusive and Atlas® is a trademark of OptiMA Inc.

Choose SizeShipping MethodShipping
GR-AtlasSC-011' Long Square Corner TrayUPS2 lbs$19.95
GR-AtlasSC-1818" Long Square Corner TrayUPS2.5 lbs$27.95
GR-AtlasSC-022' Long Square Corner TrayUPS3 lbs$27.95
GR-AtlasSC-033' Long Square Corner TrayUPS4 lbs$39.95
GR-AtlasSC-044' Long Square Corner TrayUPS5 lbs$51.95
GR-AtlasSC-055' Long Square Corner TrayUPS6 lbs$63.95
GR-AtlasSC-066' Long Square Corner TrayUPS10 lbs$75.95
GR-AtlasSC-077' Long Square Corner TrayUPS10 lbs$87.95
GR-AtlasSC-088' Long Square Corner TrayUPS90 lbs$99.95
GR-AtlasSC-10-210' Square Corner 2 PieceUPS12 lbs$123.95
GR-AtlasSC-12-212' Square Corner 2 PieceUPS14 lbs$147.95
GR-AtlasSC-14-214' Square Corner 2 PieceUPS16 lbs$171.95
GR-AtlasSC-16-216' Square Corner 2 PieceUPS90 lbs$195.95

  • Heavy Gauge Aluminum
  • Blade style marker tray with 90 degree square corner
  • Back Panel is 2 1/8" High
  • Blade is 1/8" thick and 2 1/4" deep
  • 7/8" of the Back Panel is above the blade
  • 1 1/8" of the Back Panel is below the blade
  • Lower back panel can be drilled through for permanent installation with wall anchors and wall screws.
  • Installation hardware is Not Included
  • Units up to 8' in length ship by UPS
  • UPS Dimensional Weights May Apply
  • Longer 2-Piece units available that ship by UPS.
  • Single section 10' and 12' units available. They ship by truck.
  • Cut tolerance of +/- ¼"
  • Custom lengths available through customer service
  • Lead-time is 2-5 business days shipping from Shrewsbury, MA
  • Made in the U.S.A.
3 Reviews
67% (2)
33% (1)
0% (0)
0% (0)
0% (0)
By Guy
October 16, 2018
Exactly what I wanted
The marker/eraser tray is deep enough to allow the erasers to seat completely, with no overhang (a real plus). It is a sturdy extrusion ( no folds), and will last for many years
By james stevens
October 17, 2015
Good quality product
Good as product that is part of a complete whiteboard
By Brian Giguere
February 19, 2015
Nice tray
Tray is quite nice, clean finish, no sharp edges, came packaged very well with no damage. Thought it would have holes pre-drilled for mounting to wall, but had to drill them myself.
Merchant Response:Thank you for your order and your kind words. We made the decision not to pre-drill holes so that more options are left to the customer. Our customers use these trays in many ways and mount them with a variety of hardware and even double-sided tape. Aluminum does tend to be a very easy metal to drill into so we hope you didn\'t have too much difficulty.